ASTM D2700火花点火发动机燃料马达法辛烷值试验方法

ASTM D2700 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D2700火花点火发动机燃料马达法辛烷值试验方法

Motor O.N. correlates with commercial automotive spark-ignition engine antiknock performance under severe conditions of operation.
Motor O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of fuels and engines.
Empirical correlations that permit calculation of automotive antiknock performance are based on the general equation:

1. Scope
1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number except that this test method may not be applicable to fuel and fuel components that are primarily oxygenates. The sample fuel is tested in a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The octane number scale is defined by the volumetric composition of primary reference fuel blends. The sample fuel knock intensity is compared to that of one or more primary reference fuel blends. The octane number of the primary reference fuel blend that matches the knock intensity of the sample fuel establishes the Motor octane number.
1.2 The octane number scale covers the range from 0 to 120 octane number, but this test method has a working range from 40 to 120 octane number. Typical commercial fuels produced for automotive spark-ignition engines rate in the 80 to 90 Motor octane number range. Typical commercial fuels produced for aviation spark-ignition engines rate in the 98 to 102 Motor octane number range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Motor octane number range.
1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pounds units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For more specific hazard statements, see Section 8, 13.4.1, 14.5.1, 15.6.1, Annex A1, A2.2.3.1, A2.2.3.3(6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D1193 Specification for Reagent Water
ASTM D2268 Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography
ASTM D2360 Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography
ASTM D2699 Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D2885 Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique
ASTM D3703 Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels
ASTM D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D4175 Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D4814 Specification for Automotive Spark-Ignition Engine Fuel
ASTM D5842 Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D6304 Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM E344 Terminology Relating to Thermometry and Hydrometry
ASTM E456 Terminology Relating to Quality and Statistics
ASTM E542 Practice for Calibration of Laboratory Volumetric Apparatus
ANSI Standard
C-39.1 Requirements for Electrical Analog Indicating Instruments
Energy Institute Standard
IP224/02 Determination of Low Lead Content of Light Petroleum Distillates by Dithizone Extraction and Colorimetric Method
Index Terms
aviation rating; guide table; isooctane; knock intensity; motor octane number; n-heptane; spark-ignition engine fuel performance; toluene standardization fuel; Automotive engine fuels/oils; Knock characteristics; Motor octane number (MON); Octane number/rating;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...
 

 來源：防火網　發布時間：11/27/2013 點擊次數：1386