ASTM D2699火花点火发动机燃料研究法辛烷值试验方法

ASTM D2699 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D2699火花点火发动机燃料研究法辛烷值试验方法

Research O.N. correlates with commercial automotive spark-ignition engine antiknock performance under mild conditions of operation.
Research O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of fuels and engines.
Empirical correlations that permit calculation of automotive antiknock performance are based on the general equation:
Values of k1, k2, and k3 vary with vehicles and vehicle populations and are based on road-O.N. determinations.
Research O.N., in conjunction with Motor O.N., defines the antiknock index of automotive spark-ignition engine fuels, in accordance with Specification D4814. The antiknock index of a fuel approximates the Road octane ratings for many vehicles, is posted on retail dispensing pumps in the U.S., and is referred to in vehicle manuals.
This is more commonly presented as:
Research O.N. is also used either alone or in conjunction with other factors to define the Road O.N. capabilities of spark-ignition engine fuels for vehicles operating in areas of the world other than the United States.
Research O.N. is used for measuring the antiknock performance of spark-ignition engine fuels that contain oxygenates.
Research O.N. is important in relation to the specifications for spark-ignition engine fuels used in stationary and other nonautomotive engine applications.

1. Scope
1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Research O.N., except that this test method may not be applicable to fuel and fuel components that are primarily oxygenates. The sample fuel is tested using a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The O.N. scale is defined by the volumetric composition of PRF blends. The sample fuel knock intensity is compared to that of one or more PRF blends. The O.N. of the PRF blend that matches the K.I. of the sample fuel establishes the Research O.N.
1.2 The O.N. scale covers the range from 0 to 120 octane number but this test method has a working range from 40 to 120 Research O.N. Typical commercial fuels produced for spark-ignition engines rate in the 88 to 101 Research O.N. range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Research O.N. range.
1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pound units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8, 13.4.1, 14.5.1, 15.6.1, Annex A1, A2.2.3.1, A2.2.3.3 (6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.11.4, and X4.5.1.8.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D1193 Specification for Reagent Water
ASTM D2268 Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography
ASTM D2360 Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography
ASTM D2700 Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D2885 Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique
ASTM D3703 Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels
ASTM D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D4175 Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D4814 Specification for Automotive Spark-Ignition Engine Fuel
ASTM D5842 Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D6304 Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM E344 Terminology Relating to Thermometry and Hydrometry
ASTM E456 Terminology Relating to Quality and Statistics
ASTM E542 Practice for Calibration of Laboratory Volumetric Apparatus
ANSI Standard
ASTM C-39.1 Requirements for Electrical Analog Indicating Instruments
Energy Institute Standard
IP224/02 Determination of Low Lead Content of Light Petroleum Distillates by Dithizone Extraction and Colorimetric Method
Index Terms
guide table; isooctane; knock intensity; n-heptane; research octane number; spark-ignition engine fuel performance; toluene standardization fuel; Knock characteristics; Motor octane number (MON); Automotive engine fuels/oils; Octane number/rating; Research octane number;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...
 

 來源：防火網　發布時間：11/27/2013 點擊次數：2571