ASTM D6201进油阀沉积物形成用火花点燃式发动机无铅燃料的功率计评定标准试验方法

ASTM D6201 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
ASTM D6201进油阀沉积物形成用火花点燃式发动机无铅燃料的功率计评定标准试验方法

Test Method—The Coordinating Research Council sponsored testing to develop this test method to evaluate a fuel's tendency to form intake valve deposits.
State and Federal Legislative and Regulatory Action—Regulatory action by California Air Resources Board (CARB) and the United States Environmental Protection Agency (EPA) necessitate the acceptance of a standardized test method to evaluate the intake system deposit forming tendency of an automotive spark-ignition engine fuel.
Relevance of Results—The operating conditions and design of the engine used in this test method are not representative of all engines. These factors shall be considered when interpreting test results.
Test Validity:
Procedural Compliance—The test results are not considered valid unless the test is completed in compliance with all requirements of this test method. Deviations from the parameter limits presented in Sections 12-14 will result in an invalid test. Apply engineering judgment during conduct of the test method when assessing any anomalies to ensure validity of the test results.
Engine Compliance—A test is not considered valid unless the test engine meets the quality control inspection requirements as described in Sections 10 and 12.

1. Scope
1.1 This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels. This test method uses a Ford Ranger 2.3 L four-cylinder engine. This test method includes detailed information regarding the procedure, hardware, and operations.
1.2 The ASTM Test Monitoring Center (TMC) is responsible for engine test stand calibration as well as issuance of information letters after test method modifications are approved by Subcommittee D02.A0 and Committee D02. Users of this test method shall request copies of recent information letters from the TMC to ensure proper conduct of the test method.
1.3 The values stated in SI units are to be regarded as standard. The values in parentheses are provided for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine applicability of regulatory limitations prior to use. Specific warning statements are given throughout this test method.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D86 Test Method for Distillation of Petroleum Products at Atmospheric Pressure
ASTM D235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
ASTM D287 Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
ASTM D381 Test Method for Gum Content in Fuels by Jet Evaporation
ASTM D525 Test Method for Oxidation Stability of Gasoline (Induction Period Method)
ASTM D873 Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method)
ASTM D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D1298 Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D1744 Standard Test Method for Determination of Water in Liquid Petroleum Products by Karl Fischer Reagent5
ASTM D2427 Test Method for Determination of C2 through C5 Hydrocarbons in Gasolines by Gas Chromatography
ASTM D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D3237 Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D4814 Specification for Automotive Spark-Ignition Engine Fuel
ASTM D4953 Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
ASTM D5059 Test Methods for Lead in Gasoline by X-Ray Spectroscopy
ASTM D5190 Test Method for Vapor Pressure of Petroleum Products (Automatic Method)
ASTM D5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D5302 Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
ASTM D5482 Test Method for Vapor Pressure of Petroleum Products (Mini Method--Atmospheric)
ASTM E203 Test Method for Water Using Volumetric Karl Fischer Titration
ASTM E1064 Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration
ANSI Standard
MC96.1 Temperature Measurement-Thermocouples
Coordinating Research Council (CRC)
CRCManual16, Carburetor and Induction System Rating Manual
SAE Standard
J254 Instrumentation and Techniques for Exhaust Gas Emissions Measurement
Index Terms
automotive spark-ignition engine fuel; deposit control additive; deposits (in internal combustion engines); intake valve deposits; ASTM Test Monitoring Center (TMC2); Automotive engine fuels/oils; Deposit (internal combustion engine) formation; Dynamometer testing; Intake valve deposits; Unleaded automotive gasoline; Additives--petroleum products;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...

 來源：防火網　發布時間：11/14/2013 點擊次數：1292