ASTM D178橡胶绝缘垫子标准规范

ASTM D178 Standard Specification for Rubber Insulating Matting
ASTM D178 橡胶绝缘垫子标准规范

X1.3.1 Tests made on a cellular plastic under conditions herein prescribed can be of considerable value in comparing the rate of burning and/or extent and time of burning of different materials, in controlling manufacturing processes, or as a measure of deterioration or change in burning characteristics prior to or during use.
X1.3.2 This test method is not intended to be a criterion for fire hazard. The fire hazard created by materials depends upon the form and end use of the material. Assessment of fire hazard includes, but is not limited to, many factors, such as, ease of ignition, burning rate, flame spread, fuel contribution, intensity of burning, and products of combustion.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope
1.1 This specification covers acceptance testing of rubber insulating matting for use as a floor covering for protection of workers.
1.2 Two types of matting, differing in chemical and physical characteristics, are provided and are designated as Type I and Type II matting.
1.3 The following safety hazards caveat applies only to the test method portion, Sections 17 to 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—Rubber insulating matting should remain flexible for use through normal temperature ranges.
Note 2—Rubber as used in this specification is a generic term that includes elastomers and elastomer compounds, regardless of origin.
X1.1.1 This test method covers a small-scale horizontal laboratory screening procedure for measuring the rate, extent, or time, or a combination thereof, of burning of rigid or flexible cellular plastics in accordance with this test procedure.
X1.1.2 Materials that exhibit pronounced shrinking, curling, or melting away upon heating cannot be evaluated by this test method.
X1.1.3 This test method is not applicable to materials that cannot be ignited under the conditions of this test, or to materials that exhibit progressive combustion without flame (continued glowing or charring).
Note X1.1—The rate of burning or extent of burning of rigid cellular plastics also may be determined by Test Method D3014 where the specimen is supported vertically.
X1.1.3.1 WarningDuring the course of combustion, gases or vapors, are evolved that may be hazardous to personnel. Adequate precautions should be taken to protect the operator.
X1.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
 
2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ASTM D297 Test Methods for Rubber Products--Chemical Analysis
ASTM D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension
ASTM D471 Test Method for Rubber Property--Effect of Liquids
ASTM D518 Test Method for Rubber Deterioration--Surface Cracking
ASTM D570 Test Method for Water Absorption of Plastics
ASTM D573 Test Method for Rubber--Deterioration in an Air Oven
ASTM D1564 Discontinued 1979; Testing Flexible Cellular Materials--Slab Urethane Foam; Replaced by D 3574
ASTM D1565 Specification for Flexible Cellular Materials--Vinyl Chloride Polymers and Copolymers (Open-Cell Foam)3
ASTM D1692 Discontinued 1978; Method of Test for Rate of Burning or Extent and Time of Burning of Cellular Plastics Using a Specimen Supported by a Horizontal Screen
ASTM D2406 Discontinued 1980; Methods of Testing Flexible Cellular Materials-Molded Urethane Foam; Replaced by D 3574
ASTM D3014 Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position
American National Standard
ANSIC84.1 Voltage Ratings for Electric Power Systems and Equipment (60 Hz)
Index Terms
rubber insulating matting;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...

 來源：防火網　發布時間：12/11/2013 點擊次數：1766