防火网
本站  
設為首頁 加入收藏 網站地圖  中文版 繁体 English
 
測試服務: 機車材料防火測試 | 建築產品防火測試 | 船舶防火測試 | 飛機防火測試 | 耐火測試 | 噴射火測試 | 其他測試
   
用戶名:
密碼:
驗證碼:
   
 
主要阻燃防火認證標準
火車船舶汽車建材
 
相關測試方法 更多>>
EN ISO 9239-1:2010地
EN ISO 1182:2010
NF P 92-501
NF P 92-507
法标F级测试
法标I级测试
法国M级测试
EN ISO 1182
EN ISO 9239-1
EN 13501-1
 
首頁   美国   ASTM D6630低坡度绝热屋顶薄膜装配性能的标准指南
 

ASTM D6630低坡度绝热屋顶薄膜装配性能的标准指南

ASTM D6630 Standard Guide for Low Slope Insulated Roof Membrane Assembly Performance
ASTM D6630 低坡度绝热屋顶薄膜装配性能的标准指南

A roof assembly must work as a system. Any component of the roof assembly demonstrating an inherent weakness or inability to perform will diminish the roof system performance and service life expected. This guide lists minimum performance attributes required of low slope roof assemblies. Products not previously used as roof membrane materials require additional tests beyond the scope of this document. This guide is not intended for use on in-service roofing materials. Roof membranes and other components should conform to ASTM product standards, if available.

1. Scope
1.1 This guide lists test methods intended to establish a minimum level of performance for insulated roof membrane assemblies, and lists pertinent design guidelines and installation methods in a unified manner. Material tests and evaluations are included with and without roof insulation.
1.2 It is not possible to establish a precise correlation between laboratory tests on roof assemblies and natural weathering due to variations in geographical climate, design, material and installation.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
ASTM D2523 Practice for Testing Load-Strain Properties of Roofing Membranes
ASTM D4434 Specification for Poly(Vinyl Chloride) Sheet Roofing
ASTM D4637 Specification for EPDM Sheet Used In Single-Ply Roof Membrane
ASTM D4798 Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)
ASTM D4799 Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)
ASTM D5019 Specification for Reinforced CSM (Chlorosulfonated Polyethylene) Sheet Used in Single-Ply Roof Membrane
ASTM D5147 Test Methods for Sampling and Testing Modified Bituminous Sheet Material
ASTM D5601 Test Method for Tearing Resistance of Roofing and Waterproofing Materials and Membranes
ASTM D5602 Test Method for Static Puncture Resistance of Roofing Membrane Specimens
ASTM D5635 Test Method for Dynamic Puncture Resistance of Roofing Membrane Specimens
ASTM D5849 Test Method for Evaluating Resistance of Modified Bituminous Roofing Membrane to Cyclic Fatigue (Joint Displacement)
ASTM E96/E96M Test Methods for Water Vapor Transmission of Materials

ASCE Standard
ASCE-7 Minimum Design Loads for Buildings and Other Structures
ANSI/SPRI Standard
ANSI/SPRIRP-4 Wind Design Guide for Ballasted Single Ply Roof Systems

Index Terms
cyclical fatigue; dynamic puncture; felts; heat conditioning; moisture content; multiple ply; roofing membrane; single ply; static puncture; structural deck; temperature; thermal insulation; wind tear resistance; Decks; Low-sloped roofs; Performance--roofing materials; Puncture testing; Roofing membranes; Structural deck; Thermal insulating materials;

更多防火阻燃测试认证,请咨询中国防火网
电话:400-666-7290
网址:www.firete.com
邮箱:info@firete.com

...


 來源:防火網 發布時間:11/11/2013 點擊次數:1316

 上一條: ASTM D6513计算标准耐火试验用木框架墙超强荷载的标准规范

 下一條: ASTM D6709序列VIII火花点火发动机(CLR油试验发动机)中汽车机油评价的标准试验方法
 
 
網站首頁 | 測試服務 | 各國標準 | 新聞資訊 | 防火材料 | 會展信息 | 認證服務 | 在線咨詢 | 聯系我們
Copyright © 2009-2023 Firete.com All Right Reserved 蘇公網安備 32010502010088號
服務熱線:+86 25-86583475   備案號:苏ICP备10201999号-1 DIN5510-2 DIN5510 防火網博客