ASTM C1482聚酰亚胺柔性多孔隔热和隔声材料标准规范

ASTM C1482 Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
ASTM C1482 聚酰亚胺柔性多孔隔热和隔声材料标准规范

This specification covers the composition and physical properties of lightweight, flexible open-cell polyimide foam insulation intended for use as thermal and sound-absorbing insulation for a certain temperature range in commercial and industrial environments. The insulations are classified into the following types: Types I, II, III, IV, V, and VI. Polyimide foam shall be manufactured from the appropriate monomers, and necessary compounding ingredients. Different test methods shall be performed in order to determine the following properties of the insulation: density, apparent thermal conductivity, upper temperature limit, high temperature stability, compressive strength, compression deflection, compression set, steam aging, corrosiveness, chemical resistance, surface burning characteristics, radiant panel surface flammability, vertical burn, heat release rate, specific optical smoke density, hydrogen halides in smoke, toxic gas generation, and sound absorption coefficients.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope
1.1 This specification covers the composition and physical properties of lightweight, flexible open-cell polyimide foam insulation intended for use as thermal and sound-absorbing insulation for temperatures from -328°F up to +572°F (-200°C and +300°C) in commercial and industrial environments.
1.1.1 Annex A1 includes faced polyimide foam as specified by the U.S. Navy for marine applications.
1.1.2 This standard is designed as a material specification and not a design document. Physical property requirements vary by application and temperature. No single test is adequate for estimating either the minimum or maximum use temperature of polyimide foam under all possible conditions. Consult the manufacturer for specific recommendations and physical properties for specific applications.
1.1.3 The use of an appropriate vapor retarder is required in all applications where condensation could occur and cause a decrease in thermal performance or affect other system properties.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
Note 1—The subject matter of this material specification is not covered by any other ASTM specification. There is no known ISO standard covering the subject of this standard.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM C165 Test Method for Measuring Compressive Properties of Thermal Insulations
ASTM C168 Terminology Relating to Thermal Insulation
ASTM C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C302 Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation
ASTM C335 Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
ASTM C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
ASTM C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
ASTM C421 Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation
ASTM C423 Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
ASTM C447 Practice for Estimating the Maximum Use Temperature of Thermal Insulations
ASTM C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C634 Terminology Relating to Building and Environmental Acoustics
ASTM C665 Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
ASTM C1045 Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C1058 Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM C1114 Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM C1304 Test Method for Assessing the Odor Emission of Thermal Insulation Materials
ASTM C1338 Test Method for Determining Fungi Resistance of Insulation Materials and Facings
ASTM C1559 Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type)
ASTM D395 Test Methods for Rubber Property--Compression Set
ASTM D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D638 Test Method for Tensile Properties of Plastics
ASTM D2126 Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging
ASTM D3574 Test Methods for Flexible Cellular Materials--Slab, Bonded, and Molded Urethane Foams
ASTM D3675 Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source
ASTM E84 Test Method for Surface Burning Characteristics of Building Materials
ASTM E96/E96M Test Methods for Water Vapor Transmission of Materials
ASTM E176 Terminology of Fire Standards
ASTM E662 Test Method for Specific Optical Density of Smoke Generated by Solid Materials
ASTM E795 Practices for Mounting Test Specimens During Sound Absorption Tests
ASTM E800 Guide for Measurement of Gases Present or Generated During Fires
ASTM E1354 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E2231 Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
U.S. Federal Standards
DOD-E-24607 Enamel, Interior, Nonflaming (Dry), Chlorinated Alkyd Resin, Semigloss (Metric)
Private Sector Standards
TM-232 Vertical Pipe-Chase Test to Determine Flame-Propagation Characteristics of Pipe Covering
Index Terms
flexible cellular insulation; pipe insulation; polyimide; ship insulation; sound absorbing; thermal insulation; Flexible cellular materials--specifications; Pipe thermal insulation--specifications; Polyimide insulation; Ship insulation; Sound absorbing/insulating materials/applications--specifications; Thermal insulating materials--specifications;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...
 

 来源：防火网　发布时间：12/26/2013 点击次数：2214