ASTM E1591确定性火灾模型的获取数据用标准指南

ASTM E1591  Standard Guide for Obtaining Data for Deterministic Fire Models
ASTM E1591确定性火灾模型的获取数据用标准指南

This guide is intended primarily for users and developers of mathematical fire models. It is also useful for people conducting fire tests, making them aware of some important applications and uses for small-scale fire test results. The guide thus contributes to increased accuracy in fire model calculations, which depend greatly on the quality of the input data.
The emphasis of this guide is on zone models of compartment fires. However, other types of mathematical fire models need many of the same input variables.
Note 1—Mathematical fire models in this guide are referred to by their acronyms (see 5.4).

1. Scope
1.1 This guide describes data required as input for mathematical fire models.
1.2 Guidelines are presented on how the data can be obtained.
1.3 The emphasis in this guide is on compartment zone fire models.
1.4 The values stated in SI units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 This fire standard cannot be used to provide quantitative measures.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM D835 Specification for Refined Benzene-485
ASTM D2395 Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D3417 Test Method for Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry (DSC)
ASTM D5865 Test Method for Gross Calorific Value of Coal and Coke
ASTM E176 Terminology of Fire Standards
ASTM E408 Test Methods for Total Normal Emittance of Surfaces Using Inspection-Meter Techniques
ASTM E472 Practice for Reporting Thermoanalytical Data
ASTM E537 Test Method for The Thermal Stability Of Chemicals By Differential Scanning Calorimetry
ASTM E793 Test Method for Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry
ASTM E906 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
ASTM E967 Test Method for Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers
ASTM E968 Practice for Heat Flow Calibration of Differential Scanning Calorimeters
ASTM E1321 Test Method for Determining Material Ignition and Flame Spread Properties
ASTM E1354 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E1623 Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL)
ASTM E2058 Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA)
ASTM E2257 Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies

Index Terms
air/fuel ratio; combustion efficiency; convective heat transfer coefficient; data for fire models; density; emissivity; entrainment coefficient; fire model; flame extinction coefficient; flame spread parameter; heat of combustion; heat of gasification; heat of pyrolysis; rate of heat release; ignition temperature; mass loss rate; material properties; production rate of species; pyrolysis temperature; specific heat; thermal conductivity; and thermal inertia;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

 来源：防火网　发布时间：11/8/2013 点击次数：1786