NFPA 664木材加工和木工设备的防火防爆

NFPA 664 STANDARD FOR THE PREVENTION OF FIRES AND EXPLOSIONS IN WOOD PROCESSING AND WOODWORKING FACILITIES
NFPA 664 木材加工和木工设备的防火防爆
 
1.1 Scope. This standard shall establish the minimum requirements for fire and explosion prevention and protection of industrial, commercial, or institutional facilities that process wood or manufacture wood products, using wood or other cellulosic fiber as a substitute for or additive to wood fiber, and that process wood, creating wood chips, particles, or dust.
1.1.1 Woodworking and wood processing facilities shall include, but are not limited to, wood flour plants, industrial woodworking plants, furniture plants, plywood plants, composite board plants, lumber mills, and production-type woodworking shops and carpentry shops that are incidental to facilities that would not otherwise fall within the purview of this standard.
1.1.2* This standard shall apply to woodworking operations that occupy areas of more than 465 m2 (5000 ft2) or where dust-producing equipment requires an aggregate dust collection flow rate of more than 2549 m3/hr (1500 ft3/min).
 
Revisions in the 2012 NFPA 664 increase protection of lives and property from fires and explosions in wood processing and woodworking facilities.
Updated to reflect industry changes, the 2012 NFPA 664 Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities presents the latest requirements for the construction, operation, and protection of industrial, commercial, or institutional facilities that process wood or manufacture wood products.
Many of the revisions were made for consistency with NFPA 68 Standard on Explosion Protection by Deflagration Venting, and NFPA 69 Standard on Explosion Protection Systems. In addition, changes were made to requirements for the efficiency of dust collectors for recycling of exhaust air for consistency with the Industrial Ventilation Manual published by ACGIH.
Top 2012 NFPA 664 changes include
·    New procedures for handling 'deflagration hazard', including a new definition, a new methodology for determination of a deflagration hazard using settled bulk density to determine an allowable thickness for combustible wood, plus detailed Annex instructions on how to collect the dust sample for the new methodology
·    New section with requirements on hazard determination including access doors for inspection and fire department access of ductwork
·    Revised requirements for the use of explosion protection systems and deflagration venting on metal ducts located both indoors and outdoors
·    Reduction of the concentration criterion for allowing ducts to handle dusts without protection from 75 percent of the minimum explosible concentration (MEC) down to 25 percent of MEC to correlate with NFPA 69 Standard on Explosion Prevention Systems
·    Revised provisions for dust collectors with deflagration hazards to be equipped with a deflagration suppressions system
·    Revised criteria for deflagration relief vents on dust collectors
·    Revised requirements for recycling of air-materials separators exhaust into buildings
·    New Annex material on control system design for solid fueled burners
The 2012 NFPA 664 is a must for industrial, commercial, or detention and correction facilities that operate woodworking shops as well as wood processing facilities that manufacture wood products, those that process wood, creating wood chips, particles, or dust that occupy areas greater than 5,000 sq. ft. (465 sq. m), or those that have an aggregate dust collection flow rate greater than 1500 cu. ft. per minute (2549 cu m/hr.) In addition, this important Standard is useful for fire marshals, fire/building departments, and other AHJs which regulate the facilities and agencies that conduct inspections on these facilities. (Softbound, 70 pp., 2012)

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...
 

 来源：防火网  发布时间：12/10/2013  点击次数：1779