ASTM C610模制膨胀珍珠岩块和管形绝热材料标准规范

ASTM C610 Standard Specification for Molded Expanded Perlite Block and Pipe Thermal Insulation
ASTM C610 模制膨胀珍珠岩块和管形绝热材料标准规范

This specification covers molded expanded perlite block, fittings, and pipe thermal insulation intended for use on surfaces with temperatures of certain range. The insulation shall not have visible defects that will adversely affect its service qualities. Different test methods shall be performed in order to determine the properties of the block, fitting, and pipe insulations: density, apparent thermal conductivity, linear shrinkage after heat soaking, flexural strength, compressive strength, weight loss by tumbling, moisture content, water absorption after heat aging, surface bearing characteristics, hot-surface performance, and stress corrosion cracking of austenitic stainless steel.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. ASTM C610标准适用范围
1.1 This specification covers molded expanded perlite block, fittings, and pipe thermal insulation intended for use on surfaces with temperatures between 80 to 1200°F (27 to 649°C).
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 When the installation or use of thermal insulation materials, accessories, and systems may pose safety or health problems, the manufacturer shall provide the user appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The following safety caveat applies only to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. ASTM C610参考标准
ASTM C165 Test Method for Measuring Compressive Properties of Thermal Insulations
ASTM C168 Terminology Relating to Thermal Insulation
ASTM C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C203 Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
ASTM C302 Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation
ASTM C303 Test Method for Dimensions and Density of Preformed Block and Board-Type Thermal Insulation
ASTM C335 Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
ASTM C356 Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
ASTM C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
ASTM C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
ASTM C421 Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation
ASTM C450 Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging
ASTM C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C585 Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
ASTM C795 Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel
ASTM C1045 Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C1058 Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM C1616 Test Method for Determining the Moisture Content of Organic and Inorganic Insulation Materials by Weight
ASTM E84 Test Method for Surface Burning Characteristics of Building Materials
ASTM E136 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750C
Index Terms
block; expanded perlite; fittings; molded; pipe; thermal insulation; Block and pipe thermal insulation--specifications; Perlite thermal insulation--specifications; Pipe thermal insulation--specifications; Thermal insulating materials--specifications;

南京睿督公司全国免费咨询电话：025-8658 3475  400-603-6575
网址：www.fire-test.com  
邮箱：info@fire-test.com

...

 来源：防火网　发布时间：10/9/2015 点击次数：1821