ASTM C1289饰面硬质多孔聚异氰尿酸酯隔热板规格

ASTM C1289-2015 Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
ASTM C1289-2015 饰面硬质多孔聚异氰尿酸酯隔热板规格

1. ASTM C1289标准适用范围

1.1 This specification covers the general requirements for faced thermal insulation boards composed of rigid cellular polyisocyanurate surfaced with other materials. The insulation boards are intended for use at temperatures between??40 and 200°F (?40 and 93°C). This specification does not cover cryogenic applications. Consult the manufacturer for specific recommendations and properties in cryogenic conditions. For specific applications, the actual temperature limits shall be agreed upon by the manufacturer and the purchaser.

1.2 This standard is intended to apply to rigid cellular polyurethane-modified polyisocyanurate thermal insulation board products that are commercially acceptable as non-structural panels useful in building construction. The term polyisocyanurate encompasses the term polyurethane. For engineering and design purposes, users should follow specific product information provided by board manufacturers regarding physical properties, system design considerations and installation recommendations.

NOTE 1: See Appendix X1 for guidance on determining wind pressure resistance of panels when required for wall sheathing applications.

1.3 The use of thermal insulation materials covered by this specification is typically regulated by building codes, or other agencies that address fire performance. Where required, the fire performance of the material shall be addressed through standard fire test methods established by the appropriate governing documents.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

NOTE 2: For conversion to metric units other than those contained in this standard, refer to IEEE/ASTM SI 10.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. ASTM C1289参考标准

ASTM C168 Terminology Relating to Thermal Insulation
ASTM C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C203 Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
ASTM C208 Specification for Cellulosic Fiber Insulating Board
ASTM C209 Test Methods for Cellulosic Fiber Insulating Board
ASTM C303 Test Method for Dimensions and Density of Preformed Block and Board-Type Thermal Insulation
ASTM C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
ASTM C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C550 Test Method for Measuring Trueness and Squareness of Rigid Block and Board Thermal Insulation
ASTM C728 Specification for Perlite Thermal Insulation Board
ASTM C1045 Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C1058 Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM C1114 Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM C1177/C1177M Specification for Glass Mat Gypsum Substrate for Use as Sheathing
ASTM C1303 Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation
ASTM C1363 Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
ASTM D1621 Test Method for Compressive Properties of Rigid Cellular Plastics
ASTM D2126 Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging
ASTM E84 Test Method for Surface Burning Characteristics of Building Materials
ASTM E96/E96M Test Methods for Water Vapor Transmission of Materials

Voluntary Product Standard PS 1–09 Structural Plywood
Voluntary Product Standard PS 2–10 Performance Standard for Wood Based Structural Use Panels United States Department of Commerce, National Institute of Standards and Technology, Available from Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402
CAN/CSA and CSA Standards

CSA O121-08 (R2013) Douglas Fir Plywood
CSA O151-09 Canadian Softwood Plywood

南京睿督公司全国免费咨询电话：025-8658 3475  400-603-6575
网址：www.fire-test.com  
邮箱：info@fire-test.com

...

 来源：防火网　发布时间：9/21/2015 点击次数：2083