ASTM D240弹式量热器测定液烃燃料燃烧热的标准试验方法

ASTM D240 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
ASTM D240 弹式量热器测定液烃燃料燃烧热的标准试验方法

The heat of combustion is a measure of the energy available from a fuel. A knowledge of this value is essential when considering the thermal efficiency of equipment for producing either power or heat.
The heat of combustion as determined by this test method is designated as one of the chemical and physical requirements of both commercial and military turbine fuels and aviation gasolines.
The mass heat of combustion, the heat of combustion per unit mass of fuel, is a critical property of fuels intended for use in weight-limited craft such as airplanes, surface effect vehicles, and hydrofoils. The range of such craft between refueling is a direct function of the heat of combustion and density of the fuel.

1. Scope
1.1 This test method covers the determination of the heat of combustion of liquid hydrocarbon fuels ranging in volatility from that of light distillates to that of residual fuels.
1.2 Under normal conditions, this test method is directly applicable to such fuels as gasolines, kerosines, Nos. 1 and 2 fuel oil, Nos. 1-D and 2-D diesel fuel and Nos. 0-GT, 1-GT, and 2-GT gas turbine fuels.
1.3 This test method is not as repeatable and not as reproducible as Test Method D 4809.
1.4 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 7 and 9 and A1.10 and Annex A3.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D129 Test Method for Sulfur in Petroleum Products (General Bomb Method)
ASTM D1018 Test Method for Hydrogen In Petroleum Fractions
ASTM D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D3120 Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D3701 Test Method for Hydrogen Content of Aviation Turbine Fuels by Low Resolution Nuclear Magnetic Resonance Spectrometry.
ASTM D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D4809 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)
ASTM D5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM E1 Specification for ASTM Liquid-in-Glass Thermometers
ASTM E200 Practice for Preparation, Standardization, and Storage of Standard and Reagent Solutions for Chemical Analysis
Index Terms
bomb calorimeter methods; gross heat of combustion; heat of combustion; heating tests; net heat of combustion; Bomb calorimeter methods; Combustion--petroleum products; Heating tests--petroleum products; Oxygen bomb calorimeter methods; Oxygen consumption calorimetry;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...

 来源：防火网　发布时间：12/17/2013 点击次数：1862