ASTM D5173水中碳化合物联机监视标准试验方法

ASTM D5173 Standard Test Method for On-Line Monitoring of Carbon Compounds in Water by Chemical Oxidation, by UV Light Oxidation, by Both, or by High Temperature Combustion Followed by Gas Phase NDIR or by Electrolytic Conductivity
ASTM D5173水中碳化合物联机监视标准试验方法

Accurate measurement of organic carbon in water at low and very low levels is of particular interest to the electronic, pharmaceutical, and steam power generation industries.

Elevated levels of organics in raw water tend to degrade ion exchange resin capacity. Elevated levels of organics in high purity water tend to support biological growth and, in some cases, are directly detrimental to the processes that require high purity water.

In the case of steam power generation, naturally occurring organics can become degraded to CO2 and low molecular weight organic acids that, in turn, are corrosive to the process equipment. Their effect on conductivity may also cause water chemistry operating parameters to be exceeded, calling for plant shutdown.

In process water in other industries, organic carbon can signify in-leakage of substances through damaged piping and components, or an unacceptable level of product loss.

In wastewater treatment, organic carbon measurement of influent and in-process water can help adjust optimize treatment schemes. Measurement of organic carbon at discharge may contribute to regulatory compliance.

1. Scope
1.1 This test method covers the selection, establishment, and application of monitoring systems for carbon and carbon compounds by continual sampling or continuous flow-through, automatic analysis, and recording or otherwise signaling of output data. The system chosen will depend on the purpose for which it is intended (for example, regulatory compliance, process monitoring, or to alert the user to adverse trends) and on the type of water to be monitored (low purity or high purity, with or without suspended particulates, purgeable organics, or inorganic carbon). If it is to be used for regulatory compliance, the test method published or referenced in the regulations should be used in conjunction with this test method and other ASTM test methods. The test method covers carbon concentrations of 10 g/L to 5000 mg/L.
1.2 The values stated in SI units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D1129 Terminology Relating to Water
ASTM D1193 Specification for Reagent Water
ASTM D2777 Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water
ASTM D3370 Practices for Sampling Water from Closed Conduits
ASTM D3694 Practices for Preparation of Sample Containers and for Preservation of Organic Constituents
ASTM D3864 Guide for Continual On-Line Monitoring Systems for Water Analysis
ASTM D4453 Practice for Handling of Ultra-Pure Water Samples
ASTM D4779 Test Method for Total, Organic, and Inorganic Carbon in High Purity Water by Ultraviolet (UV) or Persulfate Oxidation, or Both, and Infrared Detection
ASTM D4839 Test Method for Total Carbon and Organic Carbon in Water by Ultraviolet, or Persulfate Oxidation, or Both, and Infrared Detection

Index Terms
dissolved carbon; electrolytic conductivity; elemental carbon; inorganic carbon; non-dispersive infrared detector; on-line monitoring system; organic carbon; persulfate solution; photometric analyzer; purgeable organics; reaction chamber; reagent; total carbon; total organic carbon; wastewater treatment;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...

 来源：防火网　发布时间：11/5/2013 点击次数：2105