防火网
本站  
设为首页 加入收藏 网站地图   中文版 繁体 English
 
测试服务: 机车材料防火测试 | 建筑产品防火测试 | 船舶防火测试 | 飞机防火测试 | 耐火测试 | 喷射火测试 | 其他测试
   
用户名:
密码:
验证码:
   
 
主要阻燃防火认证标准
火车船舶汽车建材
 
相关测试方法 更多>>
EN ISO 9239-1:2010地
EN ISO 1182:2010
NF P 92-501
NF P 92-507
法标F级测试
法标I级测试
法国M级测试
EN ISO 1182
EN ISO 9239-1
EN 13501-1
 
首页   美国   ASTM D7150测定低温热应力下绝缘液体放气特性的标准试验方法
 

ASTM D7150测定低温热应力下绝缘液体放气特性的标准试验方法

ASTM D7150 Standard Test Method for the Determination of Gassing Characteristics of Insulating Liquids Under Thermal Stress at Low Temperature
ASTM D7150测定低温热应力下绝缘液体放气特性的标准试验方法

Generation of combustible gases is used to determine the condition of oil-filled electrical apparatus. Many years of empirical evidence has yielded guidelines such as those given in IEEE C57.104, IEC 60599 and IEC 61464. Industry experience has shown that electric and thermal faulted in oil-filled electrical apparatus are the usual sources that generate gases. Experience has shown that some of the gases could form in the oil at low temperatures or as a result of contamination, without any other influences.
Some severely hydro-treated transformer oils subjected to thermal stress and oils that contain certain types of contamination may produce specific gases at lower temperatures than normally expected for their generation and hence, falsely indicate abnormal operation of the electrical apparatus. Some new oils have produced large amounts of gases, especially hydrogen, without the influence of other electrical apparatus materials or electrical stresses. This renders interpretation of the dissolved gas analysis more complicated.
Heating for 164 h has been found to be a sufficient amount of time to reach a stable and characteristic gassing pattern.
This method uses both dry air and dry nitrogen as the sparging gas. This is to reflect either a electrical apparatus preservation system that allows oxygen to contact the oil or one that is sealed from the outside atmosphere. Oils sparged with air generally produce much more hydrogen as a percentage of the total combustible gas content as compared to oils sparged with nitrogen as these produce more hydrocarbons in relation to hydrogen.

1. Scope
1.1 This test method describes the procedures to determine the low temperature (120C) gassing characteristics of insulating liquids specifically and without the influence of other electrical apparatus materials or electrical stresses. This test method was primarily designed for insulating mineral oil. It can be applied to other insulating liquids in which dissolved gas-in-oil analysis (Test Method D 3612) is commonly performed.
1.2 This test method is particularly suited for detection of the phenomenon sometimes known as "stray gassing" and is also referred to in CIGRE TF11 B39.
1.3 This test method is performed on transformer insulating liquids to determine the propensity of the oil to produce certain gases such as hydrogen and hydrocarbons at low temperatures.
1.4 This test method details two procedures:
1.5 Method A describes the procedure for determining the gassing characteristics of a new, unused insulating liquid, as received, at 120C for 164 h.
1.6 Method B describes the procedure for processing the insulating liquid through an attapulgite clay column to remove organic contaminants and other reactive groups that may influence the gassing behavior of an insulating liquid, which is suspected of being contaminated. This procedure applies to both new and used insulating liquids.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D1933 Specification for Nitrogen Gas as an Electrical Insulating Material
ASTM D3612 Test Method for the Analysis of Gases Dissolved in Electrical Insulating Oil by Gas Chromatography
ASTM D3613 Practice for Sampling Insulating Liquids for Gas Analysis and Determination of Water Content
IEEE Document
ASTM C57.104 IEEE Guide for the Interpretation of Gases Generated in Oil-Immersed Transformers, 1991
IEC Documents
CIGRETF11B39 Gas formation tendency test for mineral transformer oils, 2002.
Index Terms
combustible gases; DGA; dissolved gases; dissolved gas-in-oil; insulating oil; low temperature gassing characteristics; stray gassing; transformer oil, clay treatment;

更多防火阻燃测试认证,请咨询中国防火网
电话:400-666-7290
网址:www.firete.com
邮箱:info@firete.com

...


 来源:防火网 发布时间:11/21/2013 点击次数:2012

 上一条: ASTM D7044生物可降解耐燃液压液规格

 下一条: ASTM D7151测定绝缘油中元素的标准试验方法
 
 
网站首页 | 测试服务 | 各国标准 | 新闻资讯 | 防火材料 | 会展信息 | 认证服务 | 在线咨询 | 联系我们
Copyright © 2009-2024 Firete.com All Right Reserved 苏公网安备 32010502010088号
服务热线:025-86583475   备案号:苏ICP备10201999号-1 DIN5510-2 DIN5510 防火网博客