防火网
本站  
设为首页 加入收藏 网站地图   中文版 繁体 English
 
测试服务: 机车材料防火测试 | 建筑产品防火测试 | 船舶防火测试 | 飞机防火测试 | 耐火测试 | 喷射火测试 | 其他测试
   
用户名:
密码:
验证码:
   
 
主要阻燃防火认证标准
火车船舶汽车建材
 
相关测试方法 更多>>
EN ISO 9239-1:2010地
EN ISO 1182:2010
NF P 92-501
NF P 92-507
法标F级测试
法标I级测试
法国M级测试
EN ISO 1182
EN ISO 9239-1
EN 13501-1
 
首页   政策法规   SFM 12-7A-3: Under Eave(State Fire Marshal-SFM)
 

SFM 12-7A-3: Under Eave(State Fire Marshal-SFM)

Standard: SFM 12-7A-3 – Materials and Construction Methods for Exterior Wildfire Exposure

California Department of forestry and fire protection office of the state fire marshal 
SFM 12-7A-1 Exterior Wall siding and sheathing
SFM 12-7A-2 Exterior Window
SFM 12-7A-3 Under Eave
SFM 12-7A-4 Decking
SFM 12-7A-5 Ignition Resistant material

Certification Required: Yes. The State Fire Marshal (SFM) 12-7A-3 is required in any and all jurisdictions that reference the Wildland Urban-Interface (WUI) Code as well as the California Referenced Standards Code. These are typically referenced in areas identified as high-risk areas for wildland fires near residential/commercial areas. With the increasing occurrences and scale of wildland fires, it is paramount for manufacturers to research where their products are being placed and the applicable codes of where their products are being applied/installed.

Scope: The test evaluates the fire-resistance performance of horizontal projection assemblies when exposed to a direct flame.

Applicable Products: Horizontal soffits of roof eaves, floor projections, and exposed underfloor areas

Test Procedure: Triplicate testing is required. The projection is installed above a noncombustible 4 ft. wide x 8 ft. high simulated wall assembly. a 12 in. wide x 12 in. long propane-fueled burner is placed at the base of the wall assembly is ignited and set to an output of 300 kW. The exposure is concluded when flame penetration of the eave occurs or 10-minutes. Observation continues for an additional 30-minutes if flame penetration does not occur.

Three requirements are to be met for all triplicate tests:

1.Absence of flame penetration of the eaves or horizontal projection assembly at any time.
2.Absence of structural failure of the eaves or horizontal projection subassembly at any time.
3.Absence of sustained combustion of any kind at the conclusion of the 40-minute test.

End Result: Pass/Fail criteria

√ Contact Us:

If you would like further information or pricing on SFM 12-7A-3 - please contact us

Tel: +86 25 86583475          +86 25 86583465
Website: www.fire-test.com    www.firete.com
Mail: info@fire-test.com 

……

 来源:防火网 发布时间:4/28/2023 点击次数:852

 上一条: 制动软管FMVSS106测试/ CNAS资质及澳洲NATA资质

 下一条: 玻璃纤维网格布保温ETA认证EAD 040083-00-0404
 
 
网站首页 | 测试服务 | 各国标准 | 新闻资讯 | 防火材料 | 会展信息 | 认证服务 | 在线咨询 | 联系我们
Copyright © 2009-2024 Firete.com All Right Reserved 苏公网安备 32010502010088号
服务热线:025-86583475   备案号:苏ICP备10201999号-1 DIN5510-2 DIN5510 防火网博客